Create an MX profile

Profiling steps for making an MX profile or PMM

A. Define the printer profile

    1. In the Calibrator select the printer that you want to create a profile for.
    2. Fill in media name.
    3. Click Next
    4. In the Print mode setting select the driver settings you want to use for this media/printer setup, and reference this in the naming. This will include ink set, resolution and speed.
    5. Click Next.
    6. If desired: give an extra optional comment for the profile in the bottom text box.
    7. Click Next.

The Calibrator Wizard shows the stages on the left hand side. It is possible to exit a profile creation and return to it later, when closing the Wizard the option to Save the executed steps will appear.  To resume, please double click the profile.

B. Ink Restriction: Printer linearization

Before you print the linearisation chart, please select the measuring device (Spectrophotometer) you’ll use for measuring the charts.  Each measuring device has its own linearisation chart.

Measuring the linearization chart

  1. Ensure the charts fit the media by specifying the Media dimensions in the RIP and checking the ‘Settings’ button (between the Print and Measuring Device buttons).
  2. Click Print to produce the linearization target. PrintFactory starts a print job named ‘Linearization Test Chart’ directly from the Calibrator.
    The resulting linearization target contains one 18-patch step wedge for each channel/print head. It is important that the machine outputs this chart and all subsequent charts in the same way as the live jobs are to be produced. This will optimise the results.
  3. Allow at least 15-30 minutes for the linearization target to dry unless the chart is obviously too wet.
  4. Check the linearization target and make sure that it does not contain any patches which are:
    • Too wet to measure
    • Dry, but too thick (too wet on application)
    • Non-uniform in gloss
    • Mottled
    • Sticky
    • Swollen
    If the target shows any of these above-mentioned symptoms, you will have to cut off patches and reprint it to be able to take accurate measurements.
    If necessary, use the cutter tool and click the patches which are too wet or too solid. PrintFactory marks patches selected for cropping with an X, and does not allow you to skip over adjacent patches. After cutting, you need to reprint the linear file.
  5. Click Measure 
    • Before you start measuring, the window shows the linearization target as gray. Each step wedge transforms into color patches as you measure the printed chart.
    • Import/Export buttons: You can import or export measure data in *.csv format. It is advised to save each measured chart during the processes as this will allow you to upload the data later on without re-measuring it.
  6. Click Next.

C. Ink Splitting

Here you have full control of the ink split between light and dark inks.  Check if ink curves are smooth with no peaks or dips.  More info on this item can be found in Full light Ink control.


D. Ink bleeding

The ink bleeding chart evaluates the effects of the proposed ink limits and linearization on the behaviour of the target printer setup/media combination.

The chart demonstrates ink usage as limited by the previous steps in this procedure. Visual examination is the basis for further limiting ink usage.


Proceed as follows:

  1. Click Print to produce the ink bleeding chart. PrintFactory starts a print job named ‘Ink bleeding’ directly from the Calibrator.
  2. Examine the ink bleeding chart immediately, without waiting for it to dry. Study the patches from right to left (more ink to less ink), paying particular attention to identify physical problems.

Single ink limit:

Judging the target from right to left, look for uniformity issues, bleed, mottling, matting effects and other visual artefacts. If any artefacts seen, revert back to  the linearization phase (in the beginning of the procedure).

Total ink limit:

Judge from right to left until the patches show no physical problems like drying, smudging, uniformity issues, bleeding, mottling, matting effects etc. then check the % to fill in in the Wizard.

  1. Identify the first patches at which the above problems do not occur anymore.
  2. Enter the value of this column for the ink limit.
  3. Click Next.


E. Printer Colour Space: Printer Colour Test Charts

  1. Print the charts from the next window in the Calibrator ‘Printer Colour Test Charts’.
  2. Measure the four target charts matching the sheet number to the printed items.PrintFactory Calibrator
  3. Finish the PMM. The profile is then generated and added to the Calibrator profile list.  This may take several minutes.

At the end of the calibration process a summary page provides following feedback:

  • Printer name
  • Media name
  • Mode name
  • Name of the profile in the Operating System
  • Creation date
  • Internal delta E: gives an idea on the internal quality of the reference profile
  • Delta E calculated against the reference profile: gives an idea whether the printer/media combination gamut is sufficient to print to the reference profile (important for Standardized printing and proofing).


You can evaluate your profile by printing the Visual evaluation test form.

Updated on May 19, 2022

Was this article helpful?

Related Articles